A Cuplock Scaffolding system has been developed for load-bearing scaffold, working platforms and temporary access structures. Its cup locking joint connects up to four ledgers to one standard through a single clamping action, avoiding nuts and bolts at the main ledger connection. The system combines forged steel blades, vertical standards, horizontal ledgers, diagonal braces and steel planks for modular assembly across industrial, construction and maintenance applications.
The Cuplock connection uses a lower cup welded to the standard and a sliding upper cup. During assembly, forged steel blades at both ends of the ledger are placed into the lower cup. The upper cup is then moved downward and secured by hammering it into position.
This sequence creates a positive connection between the ledger and standard. Up to four ledgers can be connected at one node, allowing the scaffold bay to be extended in multiple directions without installing separate bolts for each horizontal member. The connection also supports quick dismantling when the working level or scaffold layout needs to change.
The joint design allows the same system to be assembled as modular scaffolding, birdcage scaffolding, suspended scaffolding, mobile scaffolding or supported scaffolding. The final configuration depends on the required height, bay dimensions, platform arrangement, access route, bracing plan and foundation condition.
The standard is the vertical member of the Cuplock Scaffolding system. The documented range uses a 48.3 mm pipe diameter and a 3.25 mm pipe wall thickness, with effective standard lengths from 300 mm to 3000 mm. Short standards can be used for level changes and connection adjustments, while longer standards extend the scaffold through multiple working levels.
Ledgers provide horizontal support for steel planks and help maintain the planned bay dimensions. They also connect the standards into a continuous scaffold grid. The catalogue lists ledger effective lengths from 560 mm to 3050 mm, using a 48.3 mm pipe diameter and a 3.25 mm wall thickness.
| Component | Documented Specification |
|---|---|
| Standard pipe | 48.3 mm diameter with 3.25 mm wall thickness |
| Standard effective lengths | 300 mm to 3000 mm |
| Ledger pipe | 48.3 mm diameter with 3.25 mm wall thickness |
| Ledger effective lengths | 560 mm to 3050 mm |
| Steel plank lengths | 1500 mm, 1530 mm, 1800 mm and 2400 mm |
| Steel plank widths | 240 mm, 420 mm and 500 mm |
| Steel plank thickness | 1.2 mm or 1.5 mm |
| Diagonal brace options | Coupler type or blade type |
| Jack base heights | 600 mm and 800 mm overall heights |
| U head jack heights | 600 mm and 800 mm |
| Side bracket lengths | 290 mm, 570 mm and 800 mm |
| Surface and final design | To be selected according to project requirements and engineering review |
Steel planks are fixed onto the ledgers to create working platforms for construction and maintenance crews. The documented plank range includes lengths of 1500 mm, 1530 mm, 1800 mm and 2400 mm. Available widths include 240 mm, 420 mm and 500 mm, with thicknesses of 1.2 mm or 1.5 mm.
Each plank uses welded hooks at the corners for positioning on the ledgers. Supporting beams are welded beneath the plank body, while perforated plates improve surface grip for workers moving along the platform. When a scaffold bay is wider than a single plank arrangement, an intermediate transom can provide mid-bay support.
The intermediate transom includes an integral locking device at one end to limit movement along the ledger direction during use. The catalogue lists bay lengths from 790 mm to 3050 mm. This component helps coordinate plank placement with the scaffold grid and can be selected around different platform widths.
Steel toe plates can be installed along the sides of the scaffold plank access. The documented toe plate range includes effective lengths from 830 mm to 2970 mm, all with a listed height of 180 mm. These plates help limit the movement of small tools and materials at platform edges and define the boundary of the working level.
Diagonal braces connect adjacent standards at different horizontal levels. Together with the standard and ledger, the brace forms a triangular arrangement that improves the geometric stability of the scaffold.
Two brace configurations are listed. The first uses couplers at both ends and covers bay lengths from 920 mm to 3050 mm, with effective brace lengths from 2200 mm to 3650 mm. The second uses blades bolted at both ends and locks into the cup connection. This option covers bay lengths from 920 mm to 3050 mm, with effective lengths from 2350 mm to 3650 mm.
Brace selection should follow the approved scaffold layout. Height, bay length, access openings, platform loads, ties and local support conditions must be reviewed as one complete structure rather than selected from a single component dimension.
The Cuplock range also includes stair stringers with anti-slip stair treads. The stringer is fixed to the ledger to create an inclined route between working levels. Listed options include lengths of 1800 mm and 1830 mm, with several width and stair height combinations. The diamond-strut tread pattern is intended to improve foot contact during access.
Jack bases support the lower standards and allow the scaffold height to be adjusted above the bearing surface. The catalogue lists overall heights of 600 mm and 800 mm, with 140 mm base plates and 5 mm base plate thickness. U head jacks are used where beams require support. Their listed heights are 600 mm and 800 mm, with screw diameters from 32 mm to 38 mm and a U head size of 160 x 90 x 30 mm.
Side brackets extend the scaffold platform outward for additional reach or material storage. Truss ledgers provide a deeper reinforced horizontal member for working platforms that require a different support arrangement. These accessories allow the Cuplock system to be adapted around building edges, access routes, equipment zones and temporary structures.